Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route

Y. M. Shivaprakash; B. M. Gurumurthy; M. A. Siddhartha; N. M. Siddesh Kumar; Avishek Dutta

doi:10.24247/ijmperdapr201988

Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route

Y. M. Shivaprakash, B. M. Gurumurthy, M. A. Siddhartha, N. M. Siddesh Kumar, Avishek Dutta

Department of Mechanical & Industrial Engineering Manipal Institute of Technology, Manipal

Research output: Contribution to journal › Article › peer-review

9 Citations (Scopus)

Abstract

In the present study Duralumin(DA) based Mild Steel particles (MS _p -6% wt. and 12% wt.) reinforced composite are fabricated by cold compacting the milled powders. The mechanically mixed powders are compacted in a die cavity by applying a uniaxial steady load in the range 22-38 T. The hardness of green compacts produced are increased by sintering. The SEM images showed an even dispersion of MS _p in the duralumin alloy and elemental composition is confirmed by the EDAX spectrum. The sintered specimens were further subjected to aging treatment. Compacts were soaked at 550 ⁰ C for a span of 2 h and then are quenched in water at ambient temperature. The temperatures selected for aging treatment are 100, 150, and 200 ⁰ C and hardness was checked for every 60 minutes of time. The peak hardness obtained because of aging heat treatment is found to be much better than the corresponding sintered compacts. Compacts peak aged at 100 ⁰ C exhibited better tensile strength than the rest of the other specimens.

Original language	English
Article number	IJMPERDAPR201988
Pages (from-to)	903-920
Number of pages	18
Journal	International Journal of Mechanical and Production Engineering Research and Development
Volume	9
Issue number	2
DOIs	https://doi.org/10.24247/ijmperdapr201988
Publication status	Published - 01-01-2019

All Science Journal Classification (ASJC) codes

Aerospace Engineering
Mechanical Engineering
Fluid Flow and Transfer Processes

Access to Document

10.24247/ijmperdapr201988

Cite this

Shivaprakash, Y. M., Gurumurthy, B. M., Siddhartha, M. A., Siddesh Kumar, N. M., & Dutta, A. (2019). Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route. International Journal of Mechanical and Production Engineering Research and Development, 9(2), 903-920. Article IJMPERDAPR201988. https://doi.org/10.24247/ijmperdapr201988

@article{f704a596e34d42fd8214953b0100a143,

title = "Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route",

abstract = " In the present study Duralumin(DA) based Mild Steel particles (MS p -6% wt. and 12% wt.) reinforced composite are fabricated by cold compacting the milled powders. The mechanically mixed powders are compacted in a die cavity by applying a uniaxial steady load in the range 22-38 T. The hardness of green compacts produced are increased by sintering. The SEM images showed an even dispersion of MS p in the duralumin alloy and elemental composition is confirmed by the EDAX spectrum. The sintered specimens were further subjected to aging treatment. Compacts were soaked at 550 0 C for a span of 2 h and then are quenched in water at ambient temperature. The temperatures selected for aging treatment are 100, 150, and 200 0 C and hardness was checked for every 60 minutes of time. The peak hardness obtained because of aging heat treatment is found to be much better than the corresponding sintered compacts. Compacts peak aged at 100 0 C exhibited better tensile strength than the rest of the other specimens. ",

author = "Shivaprakash, {Y. M.} and Gurumurthy, {B. M.} and Siddhartha, {M. A.} and {Siddesh Kumar}, {N. M.} and Avishek Dutta",

year = "2019",

month = jan,

day = "1",

doi = "10.24247/ijmperdapr201988",

language = "English",

volume = "9",

pages = "903--920",

journal = "International Journal of Mechanical and Production Engineering Research and Development",

issn = "2249-6890",

publisher = "Transstellar Journal Publications and Research Consultancy Private Limited (TJPRC)",

number = "2",

}

Shivaprakash, YM , Gurumurthy, BM, Siddhartha, MA, Siddesh Kumar, NM & Dutta, A 2019, 'Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route', International Journal of Mechanical and Production Engineering Research and Development, vol. 9, no. 2, IJMPERDAPR201988, pp. 903-920. https://doi.org/10.24247/ijmperdapr201988

Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route. / Shivaprakash, Y. M.; Gurumurthy, B. M.; Siddhartha, M. A. et al.
In: International Journal of Mechanical and Production Engineering Research and Development, Vol. 9, No. 2, IJMPERDAPR201988, 01.01.2019, p. 903-920.

Research output: Contribution to journal › Article › peer-review

TY - JOUR

T1 - Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route

AU - Shivaprakash, Y. M.

AU - Gurumurthy, B. M.

AU - Siddhartha, M. A.

AU - Siddesh Kumar, N. M.

AU - Dutta, Avishek

PY - 2019/1/1

Y1 - 2019/1/1

N2 - In the present study Duralumin(DA) based Mild Steel particles (MS p -6% wt. and 12% wt.) reinforced composite are fabricated by cold compacting the milled powders. The mechanically mixed powders are compacted in a die cavity by applying a uniaxial steady load in the range 22-38 T. The hardness of green compacts produced are increased by sintering. The SEM images showed an even dispersion of MS p in the duralumin alloy and elemental composition is confirmed by the EDAX spectrum. The sintered specimens were further subjected to aging treatment. Compacts were soaked at 550 0 C for a span of 2 h and then are quenched in water at ambient temperature. The temperatures selected for aging treatment are 100, 150, and 200 0 C and hardness was checked for every 60 minutes of time. The peak hardness obtained because of aging heat treatment is found to be much better than the corresponding sintered compacts. Compacts peak aged at 100 0 C exhibited better tensile strength than the rest of the other specimens.

AB - In the present study Duralumin(DA) based Mild Steel particles (MS p -6% wt. and 12% wt.) reinforced composite are fabricated by cold compacting the milled powders. The mechanically mixed powders are compacted in a die cavity by applying a uniaxial steady load in the range 22-38 T. The hardness of green compacts produced are increased by sintering. The SEM images showed an even dispersion of MS p in the duralumin alloy and elemental composition is confirmed by the EDAX spectrum. The sintered specimens were further subjected to aging treatment. Compacts were soaked at 550 0 C for a span of 2 h and then are quenched in water at ambient temperature. The temperatures selected for aging treatment are 100, 150, and 200 0 C and hardness was checked for every 60 minutes of time. The peak hardness obtained because of aging heat treatment is found to be much better than the corresponding sintered compacts. Compacts peak aged at 100 0 C exhibited better tensile strength than the rest of the other specimens.

UR - http://www.scopus.com/inward/record.url?scp=85065247869&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85065247869&partnerID=8YFLogxK

U2 - 10.24247/ijmperdapr201988

DO - 10.24247/ijmperdapr201988

M3 - Article

AN - SCOPUS:85065247869

SN - 2249-6890

VL - 9

SP - 903

EP - 920

JO - International Journal of Mechanical and Production Engineering Research and Development

JF - International Journal of Mechanical and Production Engineering Research and Development

IS - 2

M1 - IJMPERDAPR201988

ER -

Studies on mild steel particulates reinforced duralumin composite fabricated through powder metallurgy route

Abstract

All Science Journal Classification (ASJC) codes

Access to Document

Other files and links

Fingerprint

Cite this